On the Subject of Black Hexabuttons

Despite the name, this module lights up the whole bomb.

Hovering over any of the buttons will light up a non-center button. To start off, hover the center button, the button that lights up is your starting button.

Next, hover the starting button. Use the hovered button’s position as the row, and the lit up button as the column in the table below:

	TL	TR	ML	MR	BL	BR
TL	BL	TR	TL	MR	BR	ML
TR	ML	BR	MR	TR	BL	TL
ML	MR	TL	TR	BR	ML	BL
MR	TL	BL	BR	ML	TR	MR
BL	TR	MR	ML	BL	TL	BR
BR	BR	ML	BL	TL	MR	TR

The position you get from the table will be the next button to visit. If this button’s position has already been visited, go to the next position on the table in READING ORDER, wrapping around to the top left. Repeat this process until all buttons have been visited. The resulting sequence is the order for the buttons to be pressed to get a character sequence.

Pressing any of the non-center buttons will transmit a character in Morse code. If you are unable to hear, press the Status Light to enable/disable Deaf Mode. Use the resulting button’s position and the transmitted character in the table below to get your resulting letter:

	A	B	C	D	E	F	G	H	I	J	K	L	M	N	O	P	Q	R	S	T	U	V	W	X	Y	Z
TL	L	H	T	G	W	Y	R	A	Q	P	J	Z	O	D	K	X	V	F	E	S	C	B	M	I	U	N
TR	U	P	Q	C	O	T	B	E	X	A	H	Y	I	R	L	K	Z	M	F	D	S	J	G	N	V	W
ML	T	W	I	Z	Y	B	A	S	J	O	N	U	D	F	V	R	X	Q	G	C	H	E	K	M	P	L
MR	F	X	O	K	Z	W	P	L	M	N	C	D	Q	H	G	B	I	S	T	Y	R	A	U	J	E	V
BL	J	O	P	Q	F	G	T	D	R	V	M	S	X	L	Z	W	A	C	N	H	B	U	Y	K	I	E
BR	Z	C	M	W	H	O	N	F	D	K	B	G	V	Q	X	L	T	J	R	I	E	Y	A	U	S	P

	0	1	2	3	4	5	6	7	8	9
TL	9	8	1	6	3	4	7	5	0	2
TR	5	2	0	9	7	3	4	8	1	6
ML	8	0	4	7	2	6	9	1	3	5
MR	2	4	3	8	5	7	1	6	9	0
BL	1	9	7	2	8	0	5	3	6	4
BR	4	6	8	5	9	2	3	0	7	1

Finally, transmit the characters using an altered version of Tap Code. To transmit the characters, press the center button to enter transmit mode. This will cause the center button to flash.

Find the character in the table below and note the row/column that it is in. Treat the buttons as if the buttons are labeled 1 - 6 in reading order. Press the button that is equal to the row, then the button that is equal to the column.

Tapping the button for the row will make a button’s led light up in a red color. Tapping the button for the column will make that same button’s led light up in a green color indicating that the button’s character has been fully transmitted.

Do this for each letter in the correct order to disarm the module.

	1	2	3	4	5	6
1	A	B	C	D	E	F
2	G	H	I	J	K	L
3	M	N	O	P	Q	R
4	S	T	U	V	W	X
5	Y	Z	0	1	2	3
6	4	5	6	7	8	9

Morse Table